does any one know where I can get an electronic ignition
I have a 1600 kent motor with a bosch distibutor
I am after the type that replace the points only and have no box etc outside the distributor
I have contacted a couple of places but they need to know the part number of the distributor
does anyone know the part number for the 1600 bosch distributor
or what other cars this distributor was used on?
this distributor was only used on the late model mk2 1600
i am fairly sure it is the reverse direction to the pinto
mal
electronic ignition
Moderator: Moderators
13 posts
• Page 1 of 1
electronic ignition
by 356mal » Mon Jul 09, 2007 10:11 pm
- 356mal
- P Plater - C3 License
- Posts: 165
- Joined: Sun Jan 29, 2006 9:05 pm
- Location: newcastle
by Miniliteman » Tue Jul 10, 2007 6:45 am
-
Miniliteman - Open - C4 License
- Posts: 293
- Joined: Tue May 23, 2006 9:51 pm
- Location: Netherlands
by johnw » Tue Jul 17, 2007 7:11 am
Just purchased a "Hot Spark" from the US $63.82, received it yesterday. is a similar arrangement to the Pertrinix Ignitor, haven't installed yet so can't give an opinion of how well it works
-
johnw - P Plater - C3 License
- Posts: 126
- Joined: Wed Jan 03, 2007 9:18 am
- Location: Townsville, North Queensland
-
Roger Miller - Course Official
- Posts: 2319
- Joined: Wed Dec 21, 2005 4:05 pm
- Location: Adelaide, South Australia
by Miniliteman » Sun Aug 19, 2007 5:42 am
-
Miniliteman - Open - C4 License
- Posts: 293
- Joined: Tue May 23, 2006 9:51 pm
- Location: Netherlands
by Roger Miller » Sun Aug 19, 2007 9:45 am
- Attachments
-
- right- and left-hand contact breaker points.jpg (36.88 KiB) Viewed 11421 times
Last edited by Roger Miller on Sat Dec 22, 2007 9:38 am, edited 1 time in total.
-
Roger Miller - Course Official
- Posts: 2319
- Joined: Wed Dec 21, 2005 4:05 pm
- Location: Adelaide, South Australia
by Miniliteman » Mon Aug 20, 2007 1:28 am
-
Miniliteman - Open - C4 License
- Posts: 293
- Joined: Tue May 23, 2006 9:51 pm
- Location: Netherlands
by Miniliteman » Wed Sep 05, 2007 6:17 am
John,
is that MSD as in the (big) electronic boxes for Multiple Spark Discharge?
If so which type?
Can you post or email the connection diagram?
The electronic systems from MSD I have used need a "sensor" type input signal like a Hallsensor or points. Can imagine that a poweroutput like the Hotspark isn't compatible with the MSD.
Regards, Leon.
is that MSD as in the (big) electronic boxes for Multiple Spark Discharge?
If so which type?
Can you post or email the connection diagram?
The electronic systems from MSD I have used need a "sensor" type input signal like a Hallsensor or points. Can imagine that a poweroutput like the Hotspark isn't compatible with the MSD.
Regards, Leon.
-
Miniliteman - Open - C4 License
- Posts: 293
- Joined: Tue May 23, 2006 9:51 pm
- Location: Netherlands
by johnw » Wed Sep 05, 2007 6:44 pm
Yes, I'm using a Multiple Spark Discharge, MSD Blaster ignition the Hot Spark connection diagram can be downloaded from their site, see the URL below. As I said in my earlier post I am yet to get it to function connected as shown in their diagram.
http://www.hot-spark.com/msd_hot-spark.jpg
http://www.hot-spark.com/msd_hot-spark.jpg
-
johnw - P Plater - C3 License
- Posts: 126
- Joined: Wed Jan 03, 2007 9:18 am
- Location: Townsville, North Queensland
13 posts
• Page 1 of 1
Return to Electrical, Ignition & Engine Mngmt
Who is online
Users browsing this forum: No registered users and 0 guests